| | 5/8" (12 mm) Specifications | Input Voltages | CSA
CE | 200 – 480 V, 1-PH, 50/60 Hz
200 – 600 V, 3-PH, 50/60 Hz
400 V, 3-PH, 50/60 Hz |
|---|
| Input Current @12.2 kW | CSA
CE | 200/208/240/480 V, 1-PH, 70/68/58/29 A
200/208/240/480/600 V, 3-PH, 42/40/35/18/17 A
380/400 V, 3-PH, 20.5/19.5 A |
|---|
| Output current | | 25 - 85 A |
|---|
| Rated output voltage | | 143 VDC |
|---|
| Duty cycle @ 40°C (104°F) | CSA
CE | 60% @ 85 A, 230 – 600 V, 3-PH
60% @ 85 A, 480 V, 1-PH
50% @ 85 A, 240 V, 1-PH
50% @ 85 A, 200 – 208 V, 3-PH
40% @ 85 A, 200 – 208 V, 1-PH
100% @ 66 A, 230 – 600 V, 1/3-PH
60% @ 85 A, 380/400 V, 3-PH
100% @ 66 A, 380/400 V, 3-PH |
|---|
| Open circuit voltage (OCV) | CSA
CE | 305 VDC
270 VDC |
|---|
| Dimensions with handles | | 19.7" (500 mm) D; 9.2" (234 mm) W;
17.9" (455 mm) H |
|---|
| Weight with 25' (7.6 m) torch | CSA
CE | 71 lbs (32 kg)
62 lbs (28 kg) |
|---|
| Gas Supply | | Clean, dry, oil-free air or nitrogen |
|---|
Recommended gas inlet
flow rate / pressure | Cutting: 400 scfh, 6.7 scfm (189 l/min) @ 85 psi (5.6 bar)
Gouging: 450 scfh, 7.5 scfm (212 l/min) @ 70 psi (4.8 bar) |
|---|
| Input power cable length | | 10' (3 m) |
|---|
| Power supply type | | Inverter - IGBT |
|---|
Engine-driven generator operation | Engine Drive
Rating (kW) | System Output
(amps) | Performance
(arc stretch) |
|---|
| 20 | 85 | Full | | 15 | 70 | Limited | | 15 | 60 | Full | | 12 | 60 | Limited | | 12 | 40 | Full | | 8 | 40 | Limited | | 8 | 30 | Full |
Cut Chart | Material | Thickness | Current | Maximum cut speed* |
|---|
| | inches | mm | amps | ipm | mm/min |
|---|
| Mild Steel | 10 GA
1/4
1/2
3/4
1
1-1/4 | 3
6
12
19
25
32 | 45
85
85
85
85
85 | 205
200
70
36
21
14 | 5000
5330
2000
920
560
350 |
|---|
| Stainless Steel | 1/4
1/2
3/4
1 | 6
12
19
25 | 85
85
85
85 | 205
60
30
18 | 5850
1750
770
475 |
|---|
| Aluminum | 1/4
1/2
3/4
1 | 6
12
19
25 | 85
85
85
85 | 215
85
46
25 | 6200
2400
1170
670 |
|---|
* Maximum cut speeds are the results of Hypertherm’s laboratory testing.
For optimum cut performance, actual cutting speeds may vary based on different cutting applications.
Refer to the operator manual for more details.
| |
